This investigation provides experimental results and nonlinear analysis by using finite element model of thick hollow core slab made from recycled lightweight material. Four hollow core slabs specimens were cast and tested in this investigation with dimensions (1200mm length, 450mm width and 250mm thickness). The crushed clay brick was used as a coarse aggregate instead of gravel. The iron powder waste and silica fume were used in order to increase the compressive strength of concrete. The techniques reduction hollow length and use shear reinforcement were used to improve shear strength and avoid shear failure. The specimens were tested by applying two-line load up to failure. The experimental results were showed these techniques were resisted the shear failure significantly and works to change failure mode from shear to flexural failure. Finite element computer software program (ANSYS) was used to analysis hollow core slabs specimens and compare the experimental results with the theoretical results. Good agreement have been obtained between experimental and numerical results.
Deep beams with rectangular cross-sections are widely used in concrete structures. In the present study, reinforced concrete rectangular deep beams cast with self-compacted concrete (SCC) which contains recycled concrete as coarse aggregate (RCA) were tested under directly and indirectly loading conditions. In the experimental work, fifteen deep beams were investigated, the first parameter considered in this study was the shear span to effective depth (a/d) ratio. The other variable is the replacement ratio by which the normal coarse aggregate is replaced by RCA. The beams were cast without the use of shear reinforcement. During the tests, the response of the beams including the cracking load, the ultimate load, concrete strain, and mid-span deflection were recorded. Test results indicate that the presence of RCA caused a reduction in the values of cracking and ultimate loads. For instance, the cracking load was reduced by 9%, 23%, and 50% and the ultimate load was reduced by 2% , 23%, and 25% as RCA replacement increased by 25%, 50%, and 75% respectively for a/d ratio equals 1.0. Further, by increasing the a/d ratio, the ultimate load was decreased due to the lower contribution of arch action shear transfer in the beam with a higher (a/d) ratio.
Deep mixing technology is used to improve the engineering properties of soil. In this review, previous studies on the properties and problems of weak soils were collected and explained, focusing on silty soils found globally and locally. The study also includes a discussion of physical and chemical improvement methods, specifically (cement columns). The advantages of deep mixing technology are also covered from an engineering and economic point of view, as well as its relationship to the environmental impact, as it is one of the sustainable development techniques due to its use of environmentally friendly materials. In addition, one of the objectives of this research is to study the methods of adding cement, whether in the form of powder (dry method) or mortar (wet method). A comparison was made between them to clarify the advantages and disadvantages. It was found that what distinguishes the use of the dry method from the wet method is that the former is more common. The method's effectiveness depends on the soil's moisture content, so the technique is ineffective in soils with less than 30% water content. As cement hydration produces a cementitious gel (CSH) that binds soil particles together, leading to early strength gain, pozzolanic reactions cause increased shear strength and decreased soil compressibility. Finally, some recommendations are included in this article to understand the behavior of cement columns in improving soil and avoiding problems
The focusing in this study was on the contaminated-uncontaminated soils' properties whichstudied by performing experimental tests included, Atterberg’s limit, specific gravity, compaction,unconfined compression, and direct shear tests. Different % of crude oil was used in thecontaminated soils which are performed by mixing the soils using different percent of were oilof 3 %, 6 % and 9 % by dry weight. The main effect of oil contamination causes a reduction in theliquid and plastic limit values for clayey soil. Besides oil contamination gives a reduction in themaximum dry unit weight as well as a decreasing the optimum water content with comparisonto original soil (clayey and sandy soil). The angle of internal friction is decreased for sand whileit increases for clay is one of oil contamination results.
Ten simply supported deep beams with high strength concrete (C55 MPa) have been casted and subjected to a four-point loading test. Different parameters were examined for their influence on specimen behavior. These parameters were the shear span to overall depth ratio (a/h), the overall depth of deep beams (h), and additional anchorage length beyond the centerline of support (la). The experimental results show that the beam capacity decreases as the shear span to the overall depth ratio increases, and the overall depth and embedment length decrease. The major effect of anchorage length on the shear strength is studied. Different failure modes were observed which do not match strut-and-tie failure modes. The shear compression and anchorage failures were con-trolled in the high compressive concrete deep beams due to bottom steel yielding. Finally, the ex-perimental test results are compared with predictions of the strut-and-tie method according to the ACI 318-14 and a good agreement was found.